METclean DPF One Shot 6 x 1L and On Vehicle Applicator Kit
Everything you need to start
Offer on vehicle DPF cleaning from day one
One box with the METclean On Vehicle DPF Cleaning Applicator and six 1L bottles of METclean DPF One Shot. That is enough fluid for 12 on vehicle treatments, so the kit pays for itself on the first few jobs and you can clean soot loaded filters on the ramp or at the roadside without removing them.
On vehicle applicator gun
12 on vehicle treatments
No Stage 2 rinse
What Is in the Kit
This kit brings together the two things a technician needs to start on vehicle DPF cleaning: the applicator that delivers the fluid into the filter, and the single stage chemistry that breaks the soot down. Both are the same products our own technicians use every day at our UK HQ workshop in Weston-super-Mare.
| Item | Quantity |
|---|---|
| METclean DPF One Shot DPF cleaner, 1L bottle | 6 |
| METclean On Vehicle DPF Cleaning Advanced Applicator gun | 1 |
| German made chemical resistant nylon hose, removable | 1 |
| Machined aluminium stepped adapter | 1 |
How On Vehicle Cleaning Works
One Shot is mixed 50/50 with clean water and injected directly into the DPF through the differential pressure pipe or the exhaust gas temperature (EGT) sensor port, using the applicator and its stepped adapter. The engine is brought up to temperature first, because a warm substrate accepts the solution more readily. After a short soak with the engine off, the vehicle is run and road tested so the exhaust flow and heat carry the loosened soot and moisture out of the channels.
The applicator runs from a standard workshop airline. Most compressors delivering 5 to 8 bar will drive it, and the gun is internally regulated to atomise the fluid at 3 to 6 bar, so it soaks the soot rather than blasting the ceramic honeycomb. The semi rigid reinforced hose reaches buried sensor ports on modern Euro 6 cars and vans without dismantling the front end. Fluid may run from the tailpipe during and after treatment, so warn the customer and keep a drip tray in place. Follow the On Vehicle Instructions sheet for the full procedure.
Why Buy It as a Kit
Each 1L bottle of One Shot gives two on vehicle treatments, so six bottles give you 12 cleans before you need to reorder. A typical on vehicle clean takes 30 to 45 minutes including the soak, which turns a job that would otherwise mean removing a seized filter into a quick ramp job. For a mobile technician it opens up a genuine roadside service, because DPF cleaning can be offered without a lift or heavy dismantling.
Buying the gun and the fluid together also means you start with matched equipment. The applicator is designed around the flow and pressure the METclean chemistry needs, and One Shot is a single stage formula, so there is no Stage 2 rinse to carry and one less step on every job.
Soot, Oil and Ash: Knowing When to Use It
On vehicle One Shot treatment removes soot and oil residues only. It will not remove ash from an aged DPF, because ash is the incombustible residue left by lubricating oil additives. The on vehicle method suits lower mileage filters that have soot loaded through short journeys, failed regenerations or a since repaired fault. High mileage filters with ash loading need to come off and be cleaned on a METclean machine from the E, S or XL Series, and the same One Shot fluid can be used as a direct soak before that machine clean. Always fix any vehicle faults before treating the filter, to prevent it blocking again.
No Removal Required
Inject through an existing sensor port, so the filter stays on the vehicle and the job stays on the ramp.
12 Treatments Included
Six 1L bottles at 500ml per treatment, mixed 50/50 with clean water, give 12 on vehicle cleans.
Single Stage Formula
Water based, non flammable One Shot with no Stage 2 rinse and no second product to carry.
German Made Hose
A chemical resistant flexible pipe built to handle cleaning agents without cracking or going brittle.
Regulated Atomisation
Internally regulated flow and pressure soak the soot without high pressure blasting of the substrate.
Standard Airline
Runs from most workshop compressors supplying 5 to 8 bar, with no extra equipment needed.
| Specification | Detail |
|---|---|
| Kit contents | 6 x METclean DPF One Shot 1L, 1 x applicator gun, 1 x removable nylon hose, 1 x aluminium stepped adapter |
| Treatments in kit | 12 on vehicle treatments (2 per 1L bottle) |
| On vehicle mix | 500ml One Shot plus 500ml clean water (50/50, 1L solution) |
| Typical clean time | 30 to 45 minutes including soak |
| Applicator operating pressure | 3 to 6 bar |
| Air supply required | Standard workshop airline, 5 to 8 bar compressor |
| Application points | Differential pressure pipe or EGT sensor port |
| Fluid type | Single stage, water based, non flammable DPF cleaner, pH 11.3 (alkaline) |
| Stage 2 rinse | Not required |
| Fluid hazard classification | Danger, GHS05. Skin Irrit. 2 (H315), Eye Dam. 1 (H318) |
| Transport | Not classified as dangerous goods (ADR, RID, ADN, IMDG, ICAO/IATA) |
| Off vehicle use | One Shot also works in the METclean Lite (1L per 25L tank) or as a 1 hour direct soak before a METclean machine clean |
Read Before Use
Instructions and Safety Data Sheet
Download the full step by step instructions and read the Safety Data Sheet before use. One Shot is alkaline and classified Danger. It causes skin irritation and serious eye damage, so always wear chemical resistant gloves and eye protection. Used solution is hazardous waste and must never enter drains. Flush the applicator through with clean water after every job to protect the seals and nozzle.
💡 Mobile Eco Tuning Pro Tip:
Treat the on vehicle clean as your first line of recovery, and prove it with data. Before you inject, record the DPF differential pressure at idle and at a steady 2500 RPM with your diagnostic tool, then take the same readings after the road test. A clear drop confirms the soot has gone. If the readings barely move on a high mileage filter, you are looking at ash, so quote for removal and a full clean on a METclean machine instead. Check the pressure pipes before you blame the filter, as a split, blocked or swapped pipe gives a false high reading, and where the vehicle maker calls for it, reset the soot and ash adaptation values after cleaning so the ECU relearns from a clean baseline.











